SINGLE COMPONENT WATERPROOFING SLURRY
AQUA TITE 4C is a single component polymer modified cementitious waterproofing compound. The mixed slurry greatly improves the bond strength and flexibility with concrete/sand cement screed. The product is self curing and no water is needed.
• Good abrasion resistance
• Rapid & easy application
• Single component system, no addition of liquid component except water at site
• Suitable for external and internal application
- Can be used as a waterproofing sealer on rooftops etc.
- High strength: ideal for patching as it can be feathered out with minimal cracks, and also for use in coving areas.
- Non-toxic: does not cause occupational Health & Safety concerns.
- Balconies, terraces and roof waterproofing
- Water tank - Swimming pool
- Wall and floor in wet areas (toilet, bathroom, kitchen)
- Basement of the buildings
- Foundation - prevent capillary absorption
The surface to be treated AQUA TITE 4C should be clean, sound, free from oil, grease, laitance etc. New concrete should be allowed to cure for at least 28 days prior to application of AQUA TITE 4C. New brickwork walls, sand/cement render or screeds should be left for at least 7 days before application of the AQUA TITE 4C.
Mix 20 kg of AQUA LITE 4C with 8 kg of water to get brushable consistency.
Apply the Slurry compound on the surface using brush / roller .
Powder : Water
1 : 1
Once the surface is ready and cracks are filled, apply 1 coat of the waterproofing slurry as primer.
1st Coat -
Powder : Water
1 : 0.40
Once the surface is touch dry apply 1st coat of waterproofing slurry.
2nd Coat -
Powder : Water
1 : 0.40
Apply the second coat of waterproofing slurry by brush or roller in opposite direction with respect to the 1st coat.
COMPLETE DRYING TIME
The surface shall be protected from foot traffic for 48 hours or heavy traffic / water tanks for 7 days.
- Do not apply AT 107 as a waterproofing sealer if rain is imminent.
- Do not apply if the surface temperature is below 10°C or above 35°C.
- Protect from frost.
R - 17F can be removed from tools and equipment by washing in clean water immediately after use. Any hardened material will need to be removed mechanically.
Clean tools with water before the slurry dries.
AQUA TITE 4C
@ 27 ± 1ºC
Specific Gravity (mixed material)
Water absorption by Karsten Tube after 24 hrs,on concrete block
Tensile Adhesion Strength as per EN 1348 on concrete block After 7days + 21d water.
Tensile Adhesion Strength on concrete block After 28 days
Crack overbridging After 28 days as per EN 14891
Water Impermeability After 28 days as per DIN 1048
approximately 14m²@ 0.7 mm thickness (WFT).
STORAGE AND SHELF LIFE
AQUA TITE 4C has a shelf life is approx.12 months when stored in the original unopened packaging in a dry place at 30°C and 50% relative humidity. Protect liquid from frost, do not allow to freeze.
AQUA TITE 4C is non-toxic, however if it comes into contact with the eyes, wash immediately with plenty of water and seek medical treatment. When used with mortar (which is alkaline) skin contact should be avoided. Gloves and protective clothing should be worn.
The technical details, recommendations and other information contained in this data sheet are given in good faith and represent the best of our knowledge and experience at the time of printing. It is your responsibility to ensure that our products are used and handled correctly and in accordance with any applicable Australian Standard, our instructions and recommendations and only for the uses they are intended. We also reserve the right to update information without prior notice to you to reflect our ongoing research and development program.
Country specific recommendations, depending on local standards, codes of practice, building regulations or industry guidelines, may effect specific installation recommendations.
The supply of our products and services is also subject to certain terms, warranties and exclusions, which may have already been disclosed to you in prior dealings or are otherwise available to you on request. You should make yourself familiar with them.
DISPOSAL / SPILLAGE
Spillage of any of the component products should be absorbed onto sand or other inert materials and transferred to a suitable disposable vessel. Disposal of such spillage or empty packaging should be in accordance with local waste disposal authority regulations.
CONDITIONS OF SALE
Sold subject to the Company's conditions of sale which are available on request.
The information supplied in this datasheet is based upon extensive experience and is given in good faith in order to help you. Our Company policy is one of continuous Research and Development; we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however as we have no control over site conditions or the execution of the work, we accept no liability for any loss or damage which may arise as a result thereof.